hi, can someone who does metal work link me to the right angle grinder blade, to use to clean up welds, i normally use my metal cutting blade bcos im lazy, after i have welded something, however i know this is not right, but dont know what to buy to clean up or remove metal, thank you
In reply to Post #1
Flap disc
Flap disc
In reply to Post #1
I'm no metal worker, but I have used these for flatting rough cuts, chamfering edges etc, and use masonry versions regularly
link
I'm no metal worker, but I have used these for flatting rough cuts, chamfering edges etc, and use masonry versions regularly
link
In reply to Post #2
Agree, if you are ok spending a few quid more then the flap discs are nicer to use and will remove material pretty quickly until they wear down.
https://www.toolstation.com/flap-disc/p67922
Agree, if you are ok spending a few quid more then the flap discs are nicer to use and will remove material pretty quickly until they wear down.
https://www.toolstation.com/flap-disc/p67922
In reply to Post #1
Any grinding disc about 6 mm thick will do what you want, however it's not always advisable to buy the cheapest. Some shed grit very fast and although they might cut well they will be very dirty and also not last well. Flap discs work well for light metal removal.
As you say grinding with a cutting disc is wrong and it could easily shatter.
Any grinding disc about 6 mm thick will do what you want, however it's not always advisable to buy the cheapest. Some shed grit very fast and although they might cut well they will be very dirty and also not last well. Flap discs work well for light metal removal.
As you say grinding with a cutting disc is wrong and it could easily shatter.
ok thanks ill get one of the grinding disks,
In reply to Post #6
These are the best type along with a backing pad
Just make sure you get them for the right sized spindle
I still use these whenever I need to grind down welding.
60 grit is really rough and make short work of welding finer work use a higher number
https://www.zoro.co.uk/shop/abrasives/sanding-discs/100-x-16mm-al%2Fox-fibre-discs-p80/p/ZT1032068X?utm_source=google&utm_campaign=pla%2B%7C%2BAbrasives&utm_term=ZT1032068X&utm_medium=pla_css_2&targetid=pla-394771375825&loc_physical_ms=1007097&dev=c&gclid=EAIaIQobChMI5M7Y8PGl7gIVgu_tCh01fwk1EAQYAiABEgLKz_D_BwE
https://www.zoro.co.uk/shop/power-tools/backing-pads/m14x2-0-flexible-backing-pad-for-125mm-disc-diy/p/ZT1025068X
These are the best type along with a backing pad
Just make sure you get them for the right sized spindle
I still use these whenever I need to grind down welding.
60 grit is really rough and make short work of welding finer work use a higher number
https://www.zoro.co.uk/shop/abrasives/sanding-discs/100-x-16mm-al%2Fox-fibre-discs-p80/p/ZT1032068X?utm_source=google&utm_campaign=pla%2B%7C%2BAbrasives&utm_term=ZT1032068X&utm_medium=pla_css_2&targetid=pla-394771375825&loc_physical_ms=1007097&dev=c&gclid=EAIaIQobChMI5M7Y8PGl7gIVgu_tCh01fwk1EAQYAiABEgLKz_D_BwE
https://www.zoro.co.uk/shop/power-tools/backing-pads/m14x2-0-flexible-backing-pad-for-125mm-disc-diy/p/ZT1025068X
In reply to Post #7
cheers ill have a look also
cheers ill have a look also
In reply to Post #6
As Andy mentioned, it's the flap disks you want, far superior to grinding disks, try then and you will see
As Andy mentioned, it's the flap disks you want, far superior to grinding disks, try then and you will see
In reply to Post #10
I actually think the opposite Chris, those flap wheels are ok but a proper disc cutter with grinding blade is way better imo
I actually think the opposite Chris, those flap wheels are ok but a proper disc cutter with grinding blade is way better imo
Just a quick safety message to the DIYer's looking at this thread.
ALWAYS check max rpm on disc and grinder the rpm on disc MUST be greater than that of grinder.
It is not a pretty sight when a disc explodes and the damage it can cause.
ALWAYS check max rpm on disc and grinder the rpm on disc MUST be greater than that of grinder.
It is not a pretty sight when a disc explodes and the damage it can cause.
In reply to Post #11
Depends what you're grinding, where and why i guess. I do a lot of welding and fabrication and only ever use flap discs. In fact i cant remeber the last time i used a grinding disc.
Depends what you're grinding, where and why i guess. I do a lot of welding and fabrication and only ever use flap discs. In fact i cant remeber the last time i used a grinding disc.
In reply to Post #12
Yeah it can be nasty, but if you are aware of the dangers and respect the kit it's no big deal. I've had shed loads shatter on me over the years and never had one injury because of it, that's using from little 4 inch right up to 12 inch discs. Joys of working in demo I guess
Yeah it can be nasty, but if you are aware of the dangers and respect the kit it's no big deal. I've had shed loads shatter on me over the years and never had one injury because of it, that's using from little 4 inch right up to 12 inch discs. Joys of working in demo I guess
In reply to Post #14
I had a slitting disk shatter it bounced and rode up my the side of my nose
Blood everywhere my eldest daughter **** herself when she saw the blood lol
Good job I was wearing glasses
I had a slitting disk shatter it bounced and rode up my the side of my nose
Blood everywhere my eldest daughter **** herself when she saw the blood lol
Good job I was wearing glasses
In reply to Post #15
Ouch. I've had a fair few bits hit me but never had any to the face thankfully. I use very thin 9 inch cutting discs mostly and they generally snap away from the centre rather than shatter into pieces,so I'm just left with the centre on the grinder and the outer disc usually stays stuck in whatever I'm cutting
Ouch. I've had a fair few bits hit me but never had any to the face thankfully. I use very thin 9 inch cutting discs mostly and they generally snap away from the centre rather than shatter into pieces,so I'm just left with the centre on the grinder and the outer disc usually stays stuck in whatever I'm cutting
In reply to Post #16
Lol
This one did worry me until I saw it and then
Ahh it's just a scratch
Lol
This one did worry me until I saw it and then
Ahh it's just a scratch
In reply to Post #15
Sounds nasty. I've seen pictures of quite bad cuts from discs mainly when still driven though.
Retired now but I found a face shield safer and also reduces the amount of grit you eat.
Sounds nasty. I've seen pictures of quite bad cuts from discs mainly when still driven though.
Retired now but I found a face shield safer and also reduces the amount of grit you eat.
In reply to Post #15
Some good feedback there for people
I currently work in heavy industry and have.a few welders that work for me and contractors, Nasty accident a couple of years ago now, 9 inch grinder bounced back and the lad had to have 34 stitches in his face, they take no prisoners!!!
A month ago one of our foreign plants, same again, bounced back and hit his glasses, lot of stitches.
A word of warning, all grinders are extremely dangerous, 9” ones deadly. We have a clear visor policy since the first accident. A lot of places are banning large hand held grinders and rightly so
Some good feedback there for people
I currently work in heavy industry and have.a few welders that work for me and contractors, Nasty accident a couple of years ago now, 9 inch grinder bounced back and the lad had to have 34 stitches in his face, they take no prisoners!!!
A month ago one of our foreign plants, same again, bounced back and hit his glasses, lot of stitches.
A word of warning, all grinders are extremely dangerous, 9” ones deadly. We have a clear visor policy since the first accident. A lot of places are banning large hand held grinders and rightly so
In reply to Post #19
Not the first time you've typed the words '9 inch' and 'grinder' on your phone eh scozza? ...
Not the first time you've typed the words '9 inch' and 'grinder' on your phone eh scozza? ...
In reply to Post #20
In reply to Post #19
I actually think the little 4 inch are more dangerous because people become complacent. Although yeah I've seen someone take a 9 inch blade to the face,not a pretty sight.
I actually think the little 4 inch are more dangerous because people become complacent. Although yeah I've seen someone take a 9 inch blade to the face,not a pretty sight.
In reply to Post #20
I was waiting for something like that to be fair
And I KNEW Braders would pop up
I was waiting for something like that to be fair
And I KNEW Braders would pop up
In reply to Post #19
In order to use the Pro MIG 180 on thicker materials, 208/230 volts will be needed as input voltage. Welders made by Lincoln Electric are well known for their quality, and the Lincoln Pro MIG 180 is no exception.
In terms of construction and feel, Forney Easy Weld 140 MP is excellent. In addition to its durable construction, it is lightweight as well. The weight of the machine is about 24.81 pounds. Despite its lightweight, this unit weighs only 11 1/2 kilos (11.25 kg). It is suitable for all garage-related tasks.
In order to use the Pro MIG 180 on thicker materials, 208/230 volts will be needed as input voltage. Welders made by Lincoln Electric are well known for their quality, and the Lincoln Pro MIG 180 is no exception.
In terms of construction and feel, Forney Easy Weld 140 MP is excellent. In addition to its durable construction, it is lightweight as well. The weight of the machine is about 24.81 pounds. Despite its lightweight, this unit weighs only 11 1/2 kilos (11.25 kg). It is suitable for all garage-related tasks.
This message has been suppressed by a moderator.
Reading ALL pages