Gents,
Has any one you figured out a way to take line off your spools, and save it for another time WHEN you don't want to add it to another spool/reel?
I have some 18lb fox camo I want to take off my Shimano XTB spools and put on some 40lb braid for a week long trip. I can transfer the line on some diawa spare spools I have but then I want to put the Fox line back on those spools and take the braid off for another time. It all starts to get quite difficult.
In the above scenario, without manually winding the braid back onto it's plastic delivery spool which will take me ages I can't think of another way.
Is there something available in the marketplace that doesn't cost the earth like buying a new set of spools or am I goosed?
Has any one you figured out a way to take line off your spools, and save it for another time WHEN you don't want to add it to another spool/reel?
I have some 18lb fox camo I want to take off my Shimano XTB spools and put on some 40lb braid for a week long trip. I can transfer the line on some diawa spare spools I have but then I want to put the Fox line back on those spools and take the braid off for another time. It all starts to get quite difficult.
In the above scenario, without manually winding the braid back onto it's plastic delivery spool which will take me ages I can't think of another way.
Is there something available in the marketplace that doesn't cost the earth like buying a new set of spools or am I goosed?
In reply to Post #1
Get a plastic drinks bottle and take off the lid (I find half-litre water bottles work best). Find a nut and bolt. Make a suitably sized hole in the lid and push the bolt through, with the head inside the lid. Put the nut on and tighten.
Put the bottle on the lid, then put the sticking-out bolt thread into the chuck of a drill. Tape the line to the bottle, then use the drill to wind the line around the bottle.
This can be used for storing line to be re-used, or for quickly stripping old line off spools. The top-less bottles can be stored or binned, and the top with the bolt through can be used time and time again.
Get a plastic drinks bottle and take off the lid (I find half-litre water bottles work best). Find a nut and bolt. Make a suitably sized hole in the lid and push the bolt through, with the head inside the lid. Put the nut on and tighten.
Put the bottle on the lid, then put the sticking-out bolt thread into the chuck of a drill. Tape the line to the bottle, then use the drill to wind the line around the bottle.
This can be used for storing line to be re-used, or for quickly stripping old line off spools. The top-less bottles can be stored or binned, and the top with the bolt through can be used time and time again.
In reply to Post #1
For all that faffing about I'd just buy new line
For all that faffing about I'd just buy new line
In reply to Post #3
Agreed, new line or spare spools
However, when taking line off of spools before, i have used a drill and lump of log (like stove logs), drilled into the wood and then attached line and stripped in seconds
Agreed, new line or spare spools
However, when taking line off of spools before, i have used a drill and lump of log (like stove logs), drilled into the wood and then attached line and stripped in seconds
In reply to Post #1
You have got a pod that must of cost a small fortune and you're trying save a bit of line.Stop being a tight arse and buy new line
You have got a pod that must of cost a small fortune and you're trying save a bit of line.Stop being a tight arse and buy new line
In reply to Post #5
shut up you about my pod
shut up you about my pod
In reply to Post #6
I will buy you your next 5 spools of line for it
I will buy you your next 5 spools of line for it
In reply to Post #1
Line twist/coiling could be an issue with taking line on and off especially around a small bottle, if its only short duration and you have outside space you could wrap it around some distance sticks would imagine a lot less twist in it when putting it back on, personally I would bin it and buy new.
Line twist/coiling could be an issue with taking line on and off especially around a small bottle, if its only short duration and you have outside space you could wrap it around some distance sticks would imagine a lot less twist in it when putting it back on, personally I would bin it and buy new.
In reply to Post #1
In reply to Post #7
You know you want one
You know you want one
In reply to Post #4
I've got two spare spools for my 45 QD's so I am going to wind it on there and I also have a Biomaster third reel stuffed at the back of a wardrobe somewhere so that will take the third spool. It's getting the braid back off the XTB spools then and swapping it back again which is a PIA.
I like the distance stick idea but must be looking at 200 wraps easy which might be doable, but that's just taking the braid off and I can't get it back on to a full spool.
Other than needing to swap over for this one trip it's only been used a couple of times so I'm loathed to bin it.
I've got two spare spools for my 45 QD's so I am going to wind it on there and I also have a Biomaster third reel stuffed at the back of a wardrobe somewhere so that will take the third spool. It's getting the braid back off the XTB spools then and swapping it back again which is a PIA.
I like the distance stick idea but must be looking at 200 wraps easy which might be doable, but that's just taking the braid off and I can't get it back on to a full spool.
Other than needing to swap over for this one trip it's only been used a couple of times so I'm loathed to bin it.
In reply to Post #10
It is very nice indeed
It is very nice indeed
In reply to Post #1
Stick a bolt and some washers through the old line spool it came on and put that into a drill
Just guide it on.
Open the bail arm on the reel and let it peel off
Stick a bolt and some washers through the old line spool it came on and put that into a drill
Just guide it on.
Open the bail arm on the reel and let it peel off
In reply to Post #1
I've got some spools (that are not reel spools) that I've put Nash Bullet braid on for storage - they have a drill bit connection at one end so you can use this to remove from your actual fishing spools . . .cant remember the brand / where I got them from - will dig them out and have a look . . .very useful and quick in terms of spool stripping / line storage. . .they also help when needing to load fishing spools 'in reverse' etc . . .
I've got some spools (that are not reel spools) that I've put Nash Bullet braid on for storage - they have a drill bit connection at one end so you can use this to remove from your actual fishing spools . . .cant remember the brand / where I got them from - will dig them out and have a look . . .very useful and quick in terms of spool stripping / line storage. . .they also help when needing to load fishing spools 'in reverse' etc . . .
In reply to Post #14
Berkley D - spooler I used to have one but the plastic clips went brittle they have altered the design since, carp spirit make them these days same as the old Berkley version.
BERKLEY
Carp Spirit
Berkley D - spooler I used to have one but the plastic clips went brittle they have altered the design since, carp spirit make them these days same as the old Berkley version.
BERKLEY
Carp Spirit