Chaps been fishing for 30 years and never had this before.
I bought a cheap tx shimano spod rod as my old jrc rod got snapped in the garage door (muppet)
Ive got a Okuma x spot it fitted my last rod fine but i can't get it to go on the shimano rod, i bought another okuma recently and that doesn't fit either.
Is it Okuma reals are just large or do shimano rods just have housing for shimano reels?
Anyone else had this problem?
I bought a cheap tx shimano spod rod as my old jrc rod got snapped in the garage door (muppet)
Ive got a Okuma x spot it fitted my last rod fine but i can't get it to go on the shimano rod, i bought another okuma recently and that doesn't fit either.
Is it Okuma reals are just large or do shimano rods just have housing for shimano reels?
Anyone else had this problem?
In reply to Post #1
Reel seats come in different sizes
I have had it once
Reel seats come in different sizes
I have had it once
In reply to Post #1
I've had this before with some Shimano titanos reels that wouldn't fit some 18mm reel seats, if is a old reel just sand the the foot down on either of the sides or the flat part or both if needed it probably won't take much
I've had this before with some Shimano titanos reels that wouldn't fit some 18mm reel seats, if is a old reel just sand the the foot down on either of the sides or the flat part or both if needed it probably won't take much
Not uncommon.
Lots on here will remember that the reel seat on the ESP Terry Hearn Mk2 rods struggled to house a Daiwa Tournament 5000 reel properly even though they have the same reel seat footprint as the SS3000 that Terry was using himself!!!
This is one reason why I will always take one of my reels to the shop/meet up when buying rods to make sure the reel that is going to be used on the rod fits! No seller or shop will begrudge you trying your reel first if they genuinely want to sell the rod/s!
Lots on here will remember that the reel seat on the ESP Terry Hearn Mk2 rods struggled to house a Daiwa Tournament 5000 reel properly even though they have the same reel seat footprint as the SS3000 that Terry was using himself!!!
This is one reason why I will always take one of my reels to the shop/meet up when buying rods to make sure the reel that is going to be used on the rod fits! No seller or shop will begrudge you trying your reel first if they genuinely want to sell the rod/s!
Sounds like a file will be coming out 👍
Get an old towel and soak it in hot water then place it around the Rods reel seat.
In reply to Post #6
He can't wind in with a towel
He can't wind in with a towel
In reply to Post #7
Especially a wet one !
Especially a wet one !
In reply to Post #8
A hot wet one too
A hot wet one too
Thanks chaps i might just get a different spod rod. If i take a file to anything it might go very wrong. Thanks again
In reply to Post #10
Before doing that, have a word with a rod builder about changing the reel seat for one that does fit. Could save you a loss on the spod rod when reselling it etc.
Before doing that, have a word with a rod builder about changing the reel seat for one that does fit. Could save you a loss on the spod rod when reselling it etc.
In reply to Post #4
That's strange as the MK1 Hearn reel sear fits the 5000T fine, must have changed the seat when they went to Mk2.
That's strange as the MK1 Hearn reel sear fits the 5000T fine, must have changed the seat when they went to Mk2.
In reply to Post #11
Changing seats is very expensive as they are an absolute nightmare to cut off and then get all the dried resins off, the whole handle needs to be re-done
Unless the rod is very dear, it's not worth it. You'd be better off getting a different rod or reel combo which does fit
Changing seats is very expensive as they are an absolute nightmare to cut off and then get all the dried resins off, the whole handle needs to be re-done
Unless the rod is very dear, it's not worth it. You'd be better off getting a different rod or reel combo which does fit
In reply to Post #6
The idea behind my comment was to expand the reel set. My tournies fit in a standard Fuji reel seat although initially I though they wouldn't.
The idea behind my comment was to expand the reel set. My tournies fit in a standard Fuji reel seat although initially I though they wouldn't.
In reply to Post #13
Expensive? Really? Would you class £20 as expensive as that was what I was charged by a rod builder to fit a DNPS reel seat on a rod that had lost the threads in the collar. That's a lot cheaper than buying a new rod even with the cost of the reel seat (which are not a lot for a generic style reel seat. The same rod builder charged me £30 per rod including materials to fit full duplon handles to another couple of rods as well.
Expensive? Really? Would you class £20 as expensive as that was what I was charged by a rod builder to fit a DNPS reel seat on a rod that had lost the threads in the collar. That's a lot cheaper than buying a new rod even with the cost of the reel seat (which are not a lot for a generic style reel seat. The same rod builder charged me £30 per rod including materials to fit full duplon handles to another couple of rods as well.