CarpForum.co.uk brand mark, a blue stylized fish with a white eye and a smooth modern look, set in the site header against a clean background CarpForum.co.uk wordmark in a bold flowing script style, reading CarpForum.co.uk, displayed in the site header
Menu
Utils
Go Premium Who's Online Members Weather Venues Photo Gallery Articles Events calendar
Account
Login Register
Removing Duplon handle (13 posts / 1,098 views)
chester1 chester1
Posts: 597
Post #1 11 Dec 2020 17:04
0
What's the best way of removing a Duplon grip from the butt end?

Jon Jon
Posts: 4,294
Post #2 11 Dec 2020 18:02
0
In reply to Post #1
Stanley knife.
chester1 chester1
Posts: 597
Post #3 11 Dec 2020 19:56
0
In reply to Post #2
That was my initial thought but then I saw that some people steam it to loosen the epoxy
Jon Jon
Posts: 4,294
Post #4 11 Dec 2020 20:00
0
In reply to Post #3
I suppose it depends on the glue used by the original rod builder ... I've just done some 25 yr old armalites, I cut through the duplon and peeled it off. It didn't leave much residue on the blank.
chester1 chester1
Posts: 597
Post #5 11 Dec 2020 20:11
0
In reply to Post #4
I guess there's no harm in trying the steaming method first. If it doesn't work I can use a blade. I thought it'd be a cleaner job if I did manage to just slide them off. I want to shrink wrap the handles after so I want as little gunk left on as possible. Cheers
jeffire jeffire
Posts: 4,443
Post #6 11 Dec 2020 20:27
0
In reply to Post #5
It probably wont slide off as may have masking tape underneath, you can snap duplon off or use a blade , sandpaper to get a nice smooth finish , shrink on , a piece of piss.
chester1 chester1
Posts: 597
Post #7 11 Dec 2020 20:42
0
Any thoughts on getting a reel seat off? This is escalating
jeffire jeffire
Posts: 4,443
Post #8 11 Dec 2020 23:28
0
In reply to Post #7
I take reel seats off with a dremmel , it will be epoxied on , take it slowly cut down the thread (not across) then just start snapping it off with a pair of pliers , its a bit nerve racking when you have not done it before but if you take it slowly very easy.
Zack
Posts: 3,223
Post #9 12 Dec 2020 10:01
0
As mentioned it depends on the glue used, if you can confirm its not something like an epoxy resin, you could try and use WD40 as I have used that in the past to remove adhesives. But I only discovered that by accident when I sprayed some grips once to remove grime and oil, overdid it and found the grip had become loose. It restuck down eventually when the WD40 had evapourated.

Also when I used to make rods, I might not even glue them on if they was a very tight fit or just a very small amount of araldite if need be.
chester1 chester1
Posts: 597
Post #10 12 Dec 2020 22:19
0
Mainly concerned about the reel seat now tbh. I don't have a dremel but considering buying a cheap one for the job as it seems way easier than using a hacksaw.
jeffire jeffire
Posts: 4,443
Post #11 12 Dec 2020 22:36
0
In reply to Post #10
You can do it with a jigsaw blade , is it a fuji dps ?
chester1 chester1
Posts: 597
Post #12 12 Dec 2020 23:23
0
In reply to Post #11
It is indeed. How would I go about doing it with a jigsaw without risking damaging the blank?
jeffire jeffire
Posts: 4,443
Post #13 12 Dec 2020 23:41
0
In reply to Post #12
Sorry i meant hacksaw blade !! , the dps will have masking tape although i have seen some with string underneath , keep the blade horizontal and go through the screwthread part first then snap that bit off with pliers you can then see what is underneath do the same further up , voila.
Are you sure?

This action cannot be undone.

Yes, continue

Loading…