Looking to remove my cork handle on my scopes and install new duplon handles. I'm hoping this should be quick simple as the handle can come off from the rear as the blank isn't tapered.
Has anyone done this before? And which type of adhesive would you use on the new handle?
Has anyone done this before? And which type of adhesive would you use on the new handle?
In reply to Post #1
There's probably pro builders on here who'll tell you the right way but I just used a standard slow cure two part epoxy, that way I had time to mess about if they didn't go on ok, which they did.
I also found masking the duplon was beneficial for me as I'm quite messy.
There's probably pro builders on here who'll tell you the right way but I just used a standard slow cure two part epoxy, that way I had time to mess about if they didn't go on ok, which they did.
I also found masking the duplon was beneficial for me as I'm quite messy.
In reply to Post #2
Cheers mate, I'll end up doing them twice I'm sure
Cheers mate, I'll end up doing them twice I'm sure
In reply to Post #1
Tom at Cotswold advised me to use gorilla glue for duplon. Impressed with the results on mine
Tom at Cotswold advised me to use gorilla glue for duplon. Impressed with the results on mine
In reply to Post #4
Which type did you use mate?
Which type did you use mate?
In reply to Post #1
I use gorilla glue on all my cork and duplon, be careful as it expands ,spiral around turning the blank at the same time turn the duplon on dont just push it on straight , have some isopropyl alcohol or some acetone to wipe clean , easy as .
I use gorilla glue on all my cork and duplon, be careful as it expands ,spiral around turning the blank at the same time turn the duplon on dont just push it on straight , have some isopropyl alcohol or some acetone to wipe clean , easy as .
In reply to Post #6
Cheers guys. Working out whether to try the reel seat and handle above too if it all comes off backwards without the butt eye coming off
Cheers guys. Working out whether to try the reel seat and handle above too if it all comes off backwards without the butt eye coming off
In reply to Post #7
What is the best way of getting cork off the handle please?
What is the best way of getting cork off the handle please?
In reply to Post #8
I used a pair of pliers, obviously avoiding the Blank. Just nicking it off bit by bit then sanded the rest.
I used a pair of pliers, obviously avoiding the Blank. Just nicking it off bit by bit then sanded the rest.
In reply to Post #8
The wife's hairdryer is your friend when doing this. Gently heat the handle,the epoxy underneath will become soft-ish aiding removal of the cork.
The wife's hairdryer is your friend when doing this. Gently heat the handle,the epoxy underneath will become soft-ish aiding removal of the cork.
In reply to Post #10
How easy is it to replace a reel seat?
How easy is it to replace a reel seat?
In reply to Post #11
Same,hairdryer to soften the glue,then gently keep twisting untill free.Easy enough
Same,hairdryer to soften the glue,then gently keep twisting untill free.Easy enough
In reply to Post #12
Do you need to pack the new one out with tape? Just want to know what I'm up against before I commit
Do you need to pack the new one out with tape? Just want to know what I'm up against before I commit
In reply to Post #13
Ideally you want to be replacing the reel seat with a like for like internal diameter.
If not you will have to reduce or build up tape.
It's not hard to do.
A micrometer or vernier calipers will help to get correct diameter (allowing for glue) of the tape.
Ideally you want to be replacing the reel seat with a like for like internal diameter.
If not you will have to reduce or build up tape.
It's not hard to do.
A micrometer or vernier calipers will help to get correct diameter (allowing for glue) of the tape.
In reply to Post #14
Thanks mate I'll take a look, I think it will need to come off so I can slide the top section of duplon up
Thanks mate I'll take a look, I think it will need to come off so I can slide the top section of duplon up